@zzd10h

Thanks!
I didnt really see any significant improvement.

I ran SDLBench from os4depot.




My results seems noticably lower than Slayer and radovs?

http://forum.hyperion-entertainment.b ... 2&hilit=9250+64bit#p16032


Any thoughts?

@ddni

Will try SDLBench (through SysMon, of course ;) ) this evening.

Just a thought, I tried 3 R9250 cards before.

Did yours is a 64 bits or 128bits version ?
Is yours, a "new" one ?


I tried, 2 new ones bought on ebay (red color), 64 and 128bits but the both were very slow and display was bad.

After that I bought an old one (green color) and it was really better.

@zzd10h

Dont know about the 64 or 128 bit question. However it is new from ebay and is red...

Here are my gfxbench2d results (800x600)
http://hdrlab.org.nz/benchmark/gfxbench2d/OS/AmigaOS/Result/1301

My Ragemem Write 32/64 result looks odd?



Fixed that! For some reason, my x1000 left amigakit with three 2GB RAM sticks. 2 to the left and one to the right of the cpu. I pulled the "odd" stick from the machine. Write 32/64 is now same as the comparison x1000 in ragemem.

@all
test this on opengl for results
Good test @all
http://www.clubevolution4.com/HunoSDL-Port/TestGL_Net-OS4.lha
HunoPPC

@zzd10h

How to tell the difference between the 64 and 128 bit cards?

@HunoPPC

Thanks Huno!
My results are here http://shinh.skr.jp/sdlbench/showtestgl.cgi

They look much lower than yours?

@ddni
It's normal, you use a pci (low bus) and sam440 internal bus agp (high bus) and the M9 speedup compare an 9250
Hunoppc

@huno

How does your x1000 compare?

@ddni
Your SysMon RageMem looked good, no ? (just width more the window)


My SDLbench results :

EDIT : I forgot to remove my HD card before to make the SDLBench => results were for HD6670 card.
Too lazy to unpug my HD6670...

@zzd10h

The ragemem results in the picture are BAD look at the Write 32/64
I had to remove a RAM stick to fix that.

(Resizing the window does not let the missing figures appear. Seems to be abug?)

"(Resizing the window does not let the missing figures appear. Seems to be abug?)"

If you width up the window, you don't see the whole number for
Cache L1 Read 64 and write 64 ?

Regarding your SysMon grab, actually you see "1363" and "1363" but it miss a number, it should be "1363x".
You don't see it even if you size up the window ?

@zzd10h

No, I don't see the extra numbers if I resize the window. The panel with the numbers on stays the same size.

Hello all

You can also test your 3D card with Aminet/Cow3D

As it dont use SDL nor MiniGL but only basic Warp3D so it give the maximum speed you can expect with your card (with a Warp3D driver. I hope a Gallium3D driver will be faster...)

Running simply cow3D give an fps value : it is a transform+draw speed (cpu speed + bus speed + gpu speed)
Then type 'b' it will bufferize the animation (ie no more calculate the cow rotation) and give an other fps value = this one is the "draw" speed only (bus speed + gpu speed)

Alain Thellier

@ddni
Yes you are right, with big fonts, frames are too much small.
Fixed with % resizables frames,
thank you

@thellier
Tried Cow3D.ppc on my X1000-R9250. As you know, it stalls my system after few times.
But I reach 17fps for 4-5 intervals before to freeze.

@ddni
SysMon fixed and available on OS4Depot / AmiUpdate

@zzd10h

Wow! Super fast tech support! Only Amiga makes it possible

Thanks, grabbing it now.

I confirm that the resizable window bug in sysmon is now fixed. Thanks zzd10h.

@ddni

Can anyone tell me how to fix the missing icon in Huno's Star trek archive? I get a screwdriver icon but Huno assures me there should be an icon... Incidentally, I do see the screwdriver icon quite a lot. I suspect I am missing a library of some sort.

@ddni

You are probably missing this

@Raziel

Thanks. I did not have the iconmodule drawer in my libs:
I have created it and installed png.iconmodule there. Following a reboot, I still see the screwdriver icon.